From 1b991a54cc834e8ef9ccc8bb15dce7ff70cdf8a3 Mon Sep 17 00:00:00 2001 From: Sadeep Madurange Date: Wed, 24 Dec 2025 16:29:32 +0800 Subject: Matrix post. --- _log/_site/arduino-due.html | 109 ++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 109 insertions(+) create mode 100644 _log/_site/arduino-due.html (limited to '_log/_site/arduino-due.html') diff --git a/_log/_site/arduino-due.html b/_log/_site/arduino-due.html new file mode 100644 index 0000000..172ee1a --- /dev/null +++ b/_log/_site/arduino-due.html @@ -0,0 +1,109 @@ +

This article is a step-by-step guide for programming bare-metal ATSAM3X8E chips +found on Arduino Due boards. It also includes notes on the chip’s memory layout +relevant for writing linker scripts. The steps described in this article were +tested on an OpenBSD workstation.

+ +

Toolchain

+ +

To interact directly with a bare-metal ATSAM3X8E chips, we must bypass the +embedded bootloader. To do that, we need a hardware programmer capable of +communicating with the chip over the Serial Wire Debug (SWD) protocol. Since +the workstation we upload the program from presumably doesn’t speak SWD, the +hardware programmer acts as a SWD-USB adapter. The ST-LINK/V2 programmer fits this +bill.

+ +

The OpenOCD on-chip debugger software supports +ATSAM3X8E chips. OpenOCD, on startup, runs a telnet server that we can connect to +to issue commands to the ATSAM3X8E chip. OpenOCD translates plain-text commands +into the binary sequences the chip understands, and sends them over the wire.

+ +

Finally, we need the ARM GNU Compiler +Toolchain to compile C programs for the chip. The ARM GNU compiler +toolchain and OpenOCD, as a consequence of being free software, are available +on every conceivable platform, including OpenBSD.

+ +

Electrical connections

+ +

The following photos illustrate the electrical connections between the Arduino +Due, PC, and the ST-LINK/V2 programmer required to transfer a compiled program +from a PC to the MCU.

+ + + + + + +
+ Pinout +

Wiring

+ 		+ Circuit +

Arduino Due

+
+ +

Arduino Due exposes the ATSAM3X8E’s SWD interface via its DEBUG port. The +ST-LINK/v2 programmer connects to that to communicate with the chip.

+ +

Uploading the program

+ +

The source.tar.gz tarball at the end of this page contains a sample C program +(the classic LED blink program) with OpenOCD configuration and linker scripts. +First, use the following command to build it:

+ +
$ arm-none-eabi-gcc -mcpu=cortex-m3 -mthumb -T script.ld \
+    -nostartfiles \
+    -nostdlib \
+    -o a.elf main.c
+
+ +

Then, open a telnet session with OpenOCD and issue the following sequence of +commands to configure the chip and upload the compiled program to it:

+ +
$ openocd -f openocd-due.cfg
+$ telnet localhost 4444
+  > halt
+  > at91sam3 gpnvm show
+  > at91sam3 gpnvm set 1
+  > at91sam3 gpnvm show
+$ openocd -f openocd-due.cfg -c "program a.elf verify reset exit"
+
+ +

The first of the above commands starts OpenOCD. In the telnet session, the +first command halts the chip in preparation for receiving commands. Next, we +inspect the current GPNVM bit setting (more on this later). If the bit is unset +(the gpnvm show command returns 0), we set it to 1 and verify the update.

+ +

The final command, issued from outside the telnet session, uploads the program +to the chip. Those are the bare minimum set of commands required to program the +chip. The AT91SAM3 flash driver section of the OpenOCD manual lists all +available commands for the ATSAM3X8E chip.

+ +

GPNVM bits

+ +

By design, ARM chips boot into address 0x00000. ATSAM3X8E’s memory consists of +a ROM and a dual-banked flash (flash0 and flash1), residing in different +locations of the chip’s address space. The GPNVM bits control which of them +maps to 0x00000. When GPNVM1 is cleared (the default), the chip boots from the ROM, +which contains Atmel’s SAM-BA bootloader.

+ +

Conversely, when the GPNVM1 bit is 1 (and the GPNVM2 bit is 0), flash0 at +address 0x80000 maps to 0x00000. When both GPNVM bits are 0, flash1 maps to +0x00000. Since we place our program in flash0 in the linker script, we set the +GPNVM1 bit and leave the GPNVM2 bit unchanged to ensure the chip +executes our program instead of the embedded bootloader at startup.

+ +

Linker script

+ +

At a minimum, the linker script must place the vector table at the first +address of the flash. This is mandatory for ARM chips unless we relocate the +vector table using the VTOR register.

+ +

The first entry of the vector table must be the stack pointer. The stack +pointer must be initialized to the highest memory location available to +accommodate the ATSAM3X8E’s descending stack.

+ +

The second entry of the vector table must be the reset vector. In the reset +vector, we can perform tasks such as zeroing out memory and initializing +registers before passing control to the main program.

+ +

Files: source.tar.gz

-- cgit v1.2.3