4 files changed, 173 insertions, 0 deletions
diff --git a/_site/blog/mosfet-switches/bjt.png b/_site/blog/mosfet-switches/bjt.png
new file mode 100644
index 0000000..9858fa7
--- /dev/null
+++ b/_site/blog/mosfet-switches/bjt.png
diff --git a/_site/blog/mosfet-switches/index.html b/_site/blog/mosfet-switches/index.html
new file mode 100644
index 0000000..ed63e0a
--- /dev/null
+++ b/_site/blog/mosfet-switches/index.html
@@ -0,0 +1,173 @@
+<!DOCTYPE html>
+<html>
+  <head>
+    <meta charset="utf-8">
+    <title>MOSFETs as electronic switches</title>
+
+    <head>
+  <meta charset="utf-8">
+  <meta name="viewport" content="width=device-width, initial-scale=1">
+  <title>MOSFETs as electronic switches</title>
+  <link rel="stylesheet" href="/assets/css/main.css">
+  <link rel="stylesheet" href="/assets/css/skeleton.css">
+</head>
+
+
+
+  </head>
+  <body>
+
+    <div id="nav-container" class="container">
+  <ul id="navlist" class="left">
+    
+    <li >
+      <a href="/" class="link-decor-none">hme</a>
+    </li>
+    <li class="active">
+      <a href="/blog/" class="link-decor-none">blg</a>
+    </li>
+    <li >
+      <a href="/projects/" class="link-decor-none">poc</a>
+    </li>
+    <li >
+      <a href="/about/" class="link-decor-none">abt</a>
+    </li>
+    <li><a href="/feed.xml" class="link-decor-none">rss</a></li>
+  </ul>
+</div>
+
+
+
+    <main>
+      <div class="container">
+        <div class="container-2">
+          <h2 class="center" id="title">MOSFETS AS ELECTRONIC SWITCHES</h2>
+          <h6 class="center">22 JUNE 2025</h5>
+          <br>
+          <div class="twocol justify"><p>Recently, I needed a low-power circuit for one of my battery-operated projects.
+Much of the system’s power savings depended on its ability to electronically
+switch off components, such as servos, that draw high levels of quiescent
+currents. My search for a solution led me to MOSFETs, transistors capable of
+controlling circuits operating at voltages far above their own.</p>
+
+<h2 id="acknowledgments">Acknowledgments</h2>
+
+<p>This article is a summary of what I learnt about using MOSFETs as switches.
+I’m not an electronics engineer, and this is not an authoritative guide. The
+circuits in this post must be considered within the narrow context in which
+I’ve used them. All credits for the schematics belong to <a href="https://electronics.stackexchange.com/users/292884/simon-fitch" class="external" target="_blank" rel="noopener noreferrer">Simon Fitch</a>.</p>
+
+<h2 id="preamble">Preamble</h2>
+
+<p>For a typical MOSFET-based switch, we can connect a GPIO pin of a
+microcontroller to the gate of a logic-level N-channel MOSFET placed on the low
+side of the load and tie the gate and the drain pins of the MOSFET with a
+pull-down resistor. This would work as long as the power supplies of the
+microcontroller and the load don’t share a common ground. Things become more
+complicated when they do (e.g., controlling power to a component driven by the
+same microcontroller).</p>
+
+<p>In that scenario, the source potential visible to the load is the difference
+between the gate and the threshold potentials of the MOSFET. For example, when
+the gate and the threshold potentials are 3.3 V and 1.5 V, the potential the
+load sees is 1.8 V. So, to use a low-side N-channel MOSFET, we need the gate
+potential to be higher than the source potential, which may not always be
+practical. The alternative would be a hide-side switch.</p>
+
+<h2 id="p-channel-high-side-switch">P-channel high-side switch</h2>
+
+<p>The following schematic shows how a high-side P-channel MOSFET (M1) could
+switch power to a 6 V servo driven by a 3.3 V MCU.</p>
+
+<p><img src="p_high_side.png" alt="P-channel high-side switching circuit" /></p>
+
+<p>When the microcontroller outputs low, the M2 N-channel MOSFET stops conducting.
+The R1 resistor pulls the gate of the M1 P-channel MOSFET up to +6 V, switching
+the servo off. When the microcontroller outputs high on the GPIO pin, M2’s
+source-drain connection starts conducting, causing M1’s gate potential to drop
+to 0 V, which switches on power to the servo.</p>
+
+<h2 id="n-channel-high-side-switch">N-channel high-side switch</h2>
+
+<p>The P-channel high-side switch would be the typical architecture for our use
+case. However, if we have access to a potential high enough to safely raise the
+gate potential above the threshold such that their difference outputs the source
+potential required to drive the load, we can switch on the high side using an
+N-channel MOSFET:</p>
+
+<p><img src="n_high_side.png" alt="N-channel high-side switching circuit" /></p>
+
+<p>In the schematic, both M1 and M2 are N-channel MOSFETs. When the
+microcontroller output is low, M2 stops conducting. This causes the M1’s gate
+potential to rise above the threshold, turning the servo on. Conversely, a high
+output on the GPIO line switches M2 on, which lowers M1’s gate potential. This
+switches the servo off. The R2 pull-up resistor prevents the high impedance of
+the output pins at power-up from switching the servo on.</p>
+
+<p>Both topologies require M2 to act as a level converter between circuits
+containing the microcontroller and the servo, converting between 0 V and +6 V
+or +9 V. M2 is a low-power signal converter carrying less than a milliamp of
+current. The gate-source threshold voltage of M2 must be lower than the MCU’s
+supply voltage. 2N7000, 2N7002, and BSS138 are popular choices for M2.</p>
+
+<p>The D1 flyback diodes used in the two topologies safeguard the MOSFET from
+voltage spikes caused by inductive loads such as servos.</p>
+
+<h2 id="a-bjt-alternative">A BJT alternative</h2>
+
+<p>A Bipolar Junction Transistor (BJT) is a simpler, cheaper, and more widely
+available type of transistor that can be used as a switch.</p>
+
+<p><img src="bjt.png" alt="BJT architecture" /></p>
+
+<p>In the schematic, when the MCU outputs high, Q2 starts conducting. Q2 amplifies
+Q1’s base current. Unlike MOSFETs, which are voltage-driven, BJTs are driven by
+base current. Resistors R3 and R4 must be chosen carefully to output the
+desired base currents. <a href="https://teachmetomake.wordpress.com/how-to-use-a-transistor-as-a-switch/" class="external" target="_blank" rel="noopener noreferrer">“How to choose a
+transistor as a switch”</a> is an excellent guide on using BJTs as electronic 
+switches.</p>
+
+<h2 id="which-topology-to-choose">Which topology to choose?</h2>
+
+<p>The professional community appears to prefer MOSFETs over BJTs. MOSFETs are
+more efficient when the switch is on. However, they are more challenging to
+drive, especially with a 3.3 V MCU, due to the V<sub>GS</sub> potentials
+required to achieve specified R<sub>DS(on)</sub> values (i.e., to turn them on
+fully).</p>
+
+<p>N-channel MOSFETs have lower on-resistance values, making them more efficient
+than P-channel ones. They are also cheaper. However, they are harder to drive
+on the high side as their gate potential must be higher than the source
+potential. This often requires extra circuitry such as MOSFET drivers.</p>
+
+<h2 id="further-reading">Further reading</h2>
+
+<ul>
+  <li><a href="https://www.embeddedrelated.com/showarticle/98.php" class="external" target="_blank" rel="noopener noreferrer">Different MOSFET
+topologies</a></li>
+  <li><a href="https://www.embeddedrelated.com/showarticle/809.php" class="external" target="_blank" rel="noopener noreferrer">How to read 
+MOSFET datasheets</a></li>
+  <li><a src="https://teachmetomake.wordpress.com/how-to-use-a-transistor-as-a-switch/" class="external" target="_blank" rel="noopener noreferrer">How to use a 
+transistor as a switch</a></li>
+  <li><a src="https://forum.digikey.com/t/guide-to-selecting-and-controlling-a-mosfet-for-3-3-vdc-logic-applications/42606" class="external" target="_blank" rel="noopener noreferrer">Guide to 
+selecting and controlling a MOSFET for 3.3 VDC logic applications</a></li>
+  <li><a src="https://forum.digikey.com/t/driving-a-large-relay-from-a-3-3-vdc-microcontroller-using-an-npn-darlington-transistor/41751" class="external" target="_blank" rel="noopener noreferrer">Driving a large 
+relay from a 3.3 VDC microcontroller using an NPN Darlington transistor</a></li>
+</ul>
+</div>
+          <p class="post-author right">by W. D. Sadeep Madurange</p>
+        </div>
+      </div>
+    </main>
+
+    <div class="footer">
+  <div class="container">
+    <div class="twelve columns right container-2">
+      <p id="footer-text">&copy; ASCIIMX - 2025</p>
+    </div>
+  </div>
+</div>
+
+
+  </body>
+</html>
diff --git a/_site/blog/mosfet-switches/n_high_side.png b/_site/blog/mosfet-switches/n_high_side.png
new file mode 100644
index 0000000..c851768
--- /dev/null
+++ b/_site/blog/mosfet-switches/n_high_side.png
diff --git a/_site/blog/mosfet-switches/p_high_side.png b/_site/blog/mosfet-switches/p_high_side.png
new file mode 100644
index 0000000..9f5397a
--- /dev/null
+++ b/_site/blog/mosfet-switches/p_high_side.png