Fix typography in Arduino Uno post.

1 files changed, 17 insertions, 17 deletions

diff --git a/_site/archive/arduino-uno/index.html b/_site/archive/arduino-uno/index.html
index 0c233c5..7509267 100644
--- a/_site/archive/arduino-uno/index.html
+++ b/_site/archive/arduino-uno/index.html
@@ -43,10 +43,10 @@
         <h2 class="center" id="title">PROGRAMMING ATMEGA328P CHIPS</h2>
         <h6 class="center">10 APRIL 2025</h5>
         <br>
-        <div class="twocol justify"><p>This post is a step-by-step guide for wiring up ATmega328P ICs to run at 5 V
-with a 16 MHz crystal and 3.3 V with an 8 MHz crystal. While the 5 V
-configuration is common, the 3.3 V configuration can be advantageous in
-low-power applications and when interfacing with parts that run at 3.3 V.</p>
+        <div class="twocol justify"><p>This post is a step-by-step guide for wiring up ATmega328P ICs to run at 5V
+with a 16MHz crystal and 3.3V with an 8MHz crystal. While the 5V
+configuration is common, the 3.3V configuration can be advantageous in
+low-power applications and when interfacing with parts that run at 3.3V.</p>
 
 <h2 id="5v-16mhz-configuration">5V-16MHz configuration</h2>
 
@@ -66,46 +66,46 @@ low-power applications and when interfacing with parts that run at 3.3 V.</p>
 </table>
 
 <ol>
-  <li>Connect pin 1 to 5 V via a 10 kΩ resistor.</li>
-  <li>Connect a 16 MHz crystal oscillator across pins 9 and 10.</li>
-  <li>Connect each pin of the crystal to ground via 22 pF capacitors.</li>
-  <li>Connect pins 7, 20, and 21 to 5 V.</li>
+  <li>Connect pin 1 to 5V via a 10kΩ resistor.</li>
+  <li>Connect a 16MHz crystal oscillator across pins 9 and 10.</li>
+  <li>Connect each pin of the crystal to ground via 22pF capacitors.</li>
+  <li>Connect pins 7, 20, and 21 to 5V.</li>
   <li>Connect pins 8 and 22 to ground.</li>
 </ol>
 
-<p>In addition to the connections described above, it’s a good idea to add 0.1 μF
+<p>In addition to the connections described above, it’s a good idea to add 0.1μF
 decoupling capacitors between pins 7, 20, and 21 and ground.
 <a href="Makefile">Here’s</a> a sample Makefile for avr-gcc and avrdude.</p>
 
 <h2 id="33v-8mhz-configuration">3.3V-8MHz configuration</h2>
 
 <p>The following steps use Arduino Uno as an ISP and Arduino utilities to program
-ATmega328P’s bootloader and the fuses (e.g., BOD level) for a 3.3 V supply.</p>
+ATmega328P’s bootloader and the fuses (e.g., BOD level) for a 3.3V supply.</p>
 
 <ol>
   <li>Upload the ‘ArduinoISP’ sketch to the Uno.</li>
-  <li>Wire up the ATmega328P as described in the previous section. Replace the 5 V
-supply with a 3.3 V supply and use an 8 MHz crystal instead of the 16 MHz 
+  <li>Wire up the ATmega328P as described in the previous section. Replace the 5V
+supply with a 3.3V supply and use an 8MHz crystal instead of the 16MHz 
 crystal.</li>
   <li>Connect the SPI ports (SCK, MISO, and MOSI) of the two MCUs.</li>
   <li>Connect Uno’s SS pin to the IC’s pin 1 (RESET).</li>
-  <li>The IC can be powered by the Arduino Uno’s 5 V pin.</li>
+  <li>The IC can be powered by the Arduino Uno’s 5V pin.</li>
   <li>Burn the bootloader to the ATmega328P:
     <ul>
-      <li>Select ‘ATmega328P (3.3 V, 8 MHz)’ from Tools &gt; Processor.</li>
+      <li>Select ‘ATmega328P (3.3V, 8MHz)’ from Tools &gt; Processor.</li>
       <li>Select ‘Arduino as ISP’ from Tools &gt; Programmer.</li>
       <li>Select Tools &gt; Burn Bootloader.</li>
     </ul>
   </li>
 </ol>
 
-<p>The ATmega328P is now ready to run at 8 MHz with a 3.3 V power supply. You can
+<p>The ATmega328P is now ready to run at 8MHz with a 3.3V power supply. You can
 upload programs to the ATmega328P as you usually would using avrdude.
 <a href="3v3.Makefile">Here’s</a> a sample Makefile with adjusted parameters (e.g., baud
-rate) for an 8 MHz clock.</p>
+rate) for an 8MHz clock.</p>
 
 <p>In both configurations, if you intend to use the ATmega328P’s analog-to-digital
-converter with the internal 1.1 V or AV<sub>cc</sub> voltage as reference, do
+converter with the internal 1.1V or AV<sub>cc</sub> voltage as reference, do
 not connect AREF (pin 21) to V<sub>cc</sub>. Refer to section 23.5.2 ADC
 Voltage Reference in the datasheet for more information.</p>